XINCHENG / NEWS

Taizhou Xincheng Filtration Equipment Co.,Ltd.

Check category

Causes and solutions for overheating of diaphragm filter press

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2019-04-30 11:16
  • Views:

(Summary description)In the ordinary operation of the diaphragm filter press, we often find that the diaphragm filter press has the appearance of heat.

Causes and solutions for overheating of diaphragm filter press

Causes and solutions for overheating of diaphragm filter press

Causes and solutions for overheating of diaphragm filter press

Causes and solutions for overheating of diaphragm filter press

(Summary description)In the ordinary operation of the diaphragm filter press, we often find that the diaphragm filter press has the appearance of heat.

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2019-04-30 11:16
  • Views:
Information
In the ordinary operation of the diaphragm filter press, we often find that the diaphragm filter press has the appearance of heat. This kind of heat will have a certain influence on the application of the filter press, then how can we eliminate this overheating appearance? There are two reasons for the diaphragm filter to overheat: one is the hydraulic system and the other is the filter press. The hydraulic system of the filter press is closely related to the temperature. It can control the hydraulic system through the heat release device of the device, so that the filter press can operate normally, and the demand is particularly important that the temperature of the hydraulic station should not be too high, because This will affect the hydraulic system and then cause the system to not function properly. The filter press filter plate is made of polypropylene material, which can effectively avoid overheat treatment, slow down the temperature increase, reduce the differentiation and oxidation enthalpy change of the filter press filter plate, and the application cycle of the filter plate. . Reduce the damage of the filter plate, increase the production rate, and obtain greater profit.
If the filter press is overheated, it will not only have a great impact on the operation of the staff, but also will have a certain influence on the filtrate during the operation, which will cause a change in the filtrate, and then affect the effect of separation, so in operation The process of overheating of the filter press should be noted.
1. If the diaphragm filter press bearing is found to be damaged, it must be replaced in time. When installing new bearings, it requires very strict standards. Careful and careful, do not carelessly.
2, to prevent the bearing from bringing a strong impact, to prevent the appearance of scratches, indentations, cracking.
3. In the process of using the diaphragm filter press, it is necessary to pay attention to the anti-rust treatment of the bearing at regular intervals, and do not make the water stain too much. Clean the periphery of the housing, apply lubricant, and maintain.

Scan the QR code to read on your phone

Previous: How does the filter part of the chamber filter press work?
Next: None
Previous: How does the filter part of the chamber filter press work?
Next: None

Looking forward to working with you

Taizhou Xincheng Filtration Equipment CO., Ltd was established by the investment of enterprise group, Taizhou xincheng industrial corporation. With many years’ development, the corporation has been a professional production enterprise with the research & development, design and manufacture by intergration of filter cartridge.  

CONTACT US

Tel: +86-523-83836588 
Fax:+86-523-83836599   
M.P.:+86-15152686868 (TIGER) +86-18115959699 (PATRICK)   
E-Mail: bart.tiger@hotmail.com   patrickzou2011@hotmail.com
Add: No.8 Dongsan Industrial Park,Daiyao Town, Xinghua City,Jiangsu,China

MOBILE

aizhou Xincheng Filtration Equipment CO., Ltd

Copyright © 2019 Xincheng All Rights Reserved   Powered by www.300.cn 苏ICP备1988965号